1. How To Cut Thin Slots In Wood Lathe
2. How To Cut Thin Slots In Wood Stoves
3. How To Cut Thin Slots In Wood Dowels
4. How To Cut Thin Slots In Wood Floors

WW'nTip-of-Day #055: Slot Cutting Practice - Bonus: Curtis Buchanan https://www.youtube.com/user/cur. Cutting slots in wood is often known as mortising, and it can be done with a drill press. You'll need to set up a fence guard on your drill press table to make sure you move your board straight. Attach a Forstner bit to the drill and set up the proper plunge depth. Routers can also be used to clear out a fairly large section of wood, without cutting completely through the surface. This is useful in order to create three dimensional layers in the depth of the wood. This can be a very useful technique to utilize in producing a relief type carving on the surface of a flat piece of wood.

I’m working on a new woodworking project that involved cutting through-slots for bolts in a couple of boards. The two boards will act as adjustable arms to hold a dowel handle for a garden cart.

How To Cut Thin Slots In Wood Lathe

Slots or channels cut into wood more commonly are referred to as dadoes. Slots, channels or dadoes typically are used to create stable, tight-fitting joints on plywood and lumber. Place the wood to be cut on the routing table horizontally. Using a straight-edged ruler, draw clear and accurate slots boundary on both sides. Ensure you use a sharp and visible pencil while drawing the slot lines. Set the bit size in the router.

I have cut shorter and narrower slots using a table-mounted router for a coin bank. These bolt slots were considerably longer and 1/4' wide so I was reluctant to use the same technique. I don’t have a plunge router – which would probably be the fastest and easiest way to do this.

Crowd-sourcing ideas

After checking a couple of woodworking forums for ideas – including one where someone trying this on a router table said the board 'shattered' (yikes!) – the general consensus seemed to be todrill out most of the material and clean up the slot later with a coping saw.

How To Cut Thin Slots In Wood Stoves

That sounded good (and safe) to me.

Since my slot was only 1/4' wide, I decided best approach was to use a 1/4' Forstner bit in a drill press to define the slot and remove most of the material, then clean up the slot with a file and sandpaper.

The shaft on the 1/4' bit was larger than the bit itself so I had to flip the board over to drill all the way through the 3/4' material. It’s probably a good idea to do this anyway to avoid tear-out unless you have a backer board underneath when you’re drilling.

What to do

How To Cut Thin Slots In Wood Dowels

Drilling

• Mark the centre points for each end of the slot in the blank and use a nail or awl to punch a small hole for orienting the bit.
• Set up the drill press with a Forstner bit the same size as the slot you’re cutting. You’ll need to attach a fence to the drill press table to maintain a straight line as you drill along the length.
• Place the blank against the fence and lower the bit. Adjust the fence and blank so the point of the Forstner bit enters the small punched hole. Clamp the fence in place, slide the blank to the mark at the other end of the slot and check that it’s aligned properly.
• Put a mark on the edge of the board that’s against the fence. Keep this edge against the fence when you flip the board over and drill the other side. This ensures the holes are in line even if your a hair off centre of the board.
• Turn on the drill press and drill the each end hole to define the slot – drilling about two-thirds to three-quarters of the way through the board. After that, just keep drilling holes and moving the work piece along the fence, overlapping holes just enough to keep point of the bit entering new wood. The slot will fill up with shavings which you should clear out if they get in the way.
• Once you’ve drilled the length of the slot, clean it out with a screw driver or something similar. Flip the board over (keeping the same edge against the fence).
• Repeat the process starting with the end holes. It doesn’t matter which direction you work in.

How To Cut Thin Slots In Wood Floors

A COUPLE OF NOTES:

• If you’re making a wider slot, you may want to make an additional pass to remove the 'peaks' between holes.
• If you have a mortising chisel & bit you could swap that in once you’ve drilled the end holes.

Cleaning up the slot

• After the drilling is complete, clean out the shavings with an awl or small screwdriver.
• Clamp the work piece on edge to your bench and use a flat file to remove the high points left between the drilled holes being careful not to hit the rounded ends of the slots.
• Wrap a small piece of sandpaper around a drill bit (smaller than the slot) to sand the ends of the slot.
• After filing off most of the rough surfaces in the slot, wrap some sandpaper around the file and use it to finish cleaning up the slot.

If the slots were 1/2” wide or more, I probably would have used a jigsaw and straightedge to clean up the slots before sanding.